View AP1513SG-13_5013190.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Features
* * * * * * * * * Input voltage: 3.6V to 18V Output voltage: 0.8V to VCC Duty ratio: 0% to 100% PWM control Oscillation frequency: 300KHz typ. Soft-start, Current limit, Enable function Thermal Shutdown function Built-in internal SW P-channel MOS SOP-8L: Available in "Green" Molding Compound (No Br, Sb) Lead Free Finish/ RoHS Compliant (Note 1)
General Description
AP1513 consists of step-down switching regulator with PWM control. These devices include a reference voltage source, oscillation circuit, error amplifier, and internal PMOS. AP1513 provides low-ripple power, high efficiency, and excellent transient characteristics. The PWM control circuit is able to vary the duty ratio linearly from 0 up to 100%. This converter also contains an error amplifier circuit as well as a soft-start circuit that prevents overshoot at startup. An enable function, an over current protect function and a short circuit protect function are built inside, and when OCP or SCP happens, the operation frequency will be reduced from 300KHz to 30KHz. Also, an internal compensation block is built in to minimum external component count. With the addition of an internal P-channel Power MOS, a coil, capacitors, and a diode connected externally, these ICs can function as step-down switching regulators. They serve as ideal power supply units for portable devices when coupled with the SOP-8L mini-package, providing such outstanding features as low current consumption. Since this converter can accommodate an input voltage up to 18V, it is also suitable for the operation via an AC adapter.
Applications
* * * * * * * * * PC Motherboard LCD Monitor Graphic Card DVD-Video Player Telecom Equipment ADSL Modem Printer and other Peripheral Equipment Microprocessor core supply Networking power supply
Typical Application Circuit
L1 33uH R OCSET COCSET 3K Option CIN 470uF CVcc 0.1uF REN 100K CEN 0.1uF OCSET EN RA 6.8K VOUT = 5V/2A
VIN
Vcc
Output
AP1513
FB VSS
CC Optional
+
C
+
COUT 470uF
- 0.1uFD1 SBR2U30P1 RB 1.3K
Note: VOUT = VFB x (1+RA/RB) RB =0.7K~5K ohm
VOUT L1 Value
VIN = 12V, IMAX = 2A 2.5V 3.3V 22uH 27uH
5V 33uH
AP1513 Rev. 4 DS31053
1 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Ordering Information
AP1513 S X - 13 Package S : SOP-8L Lead Free L : Lead Free G : Green Packing 13 : Tape & Reel
Device
Lead-free
AP1513SL-13 AP1513SG-13
Notes:
Package Code S S
Packaging (Note 2) SOP-8L SOP-8L
13" Tape and Reel Quantity Part Number Suffix 2500/Tape & Reel -13 2500/Tape & Reel -13
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf.
Pin Descriptions
( Top View )
FB EN 1 2 AP1513 OCSET 3 VCC 4 6 5 Output Output 8 Vss 7 Vss
SOP-8L
Pin Descriptions
Pin Name FB EN OCSET VCC Output VSS Pin No. 1 2 3 4 5, 6 7, 8 Description Feedback pin Power-off pin H: Normal operation (Step-down operation) L: Step-down operation stopped (All circuits deactivated) Add an external resistor to set max output current IC power supply pin Switch Pin. Connect external inductor/diode here. Minimize trace area at this pin to reduce EMI GND Pin
AP1513 Rev. 4 DS31053
2 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Block Diagram
Output Oscillation Circuit Vcc PWM-Switched Control Circuit Thermal Shutdown VEN 100uA Vss
+
Reference Voltage Source
FB
-
EN
OCSET
Absolute Maximum Ratings
Symbol VCC VFB VEN VOUT PD TJ TST
Caution:
Parameter VCC Pin Voltage Feedback Pin Voltage EN Pin Voltage Switch Pin Voltage Power Dissipation Operating Junction Temperature Range Storage Temperature Range
Rating VSS - 0.3 to VSS + 20 VSS - 0.3 to VCC VSS - 0.3 to VIN + 0.3 VSS - 0.3 to VIN + 0.3 Internally limited -40 to +125 -40 to +150
Unit V V V V mW
o o
C C
The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions.
Recommended Operating Conditions
Symbol VIN IOUT TA Parameter Input Voltage Output Current Operating Ambient Temperature Min 3.6 0 -20 Max 18 2 85 Unit V A o C
AP1513 Rev. 4 DS31053
3 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Electrical Characteristics
Symbol VFB IFB ISW ISSS VOUT /VOUT VOUT /VOUT fOSC fOSC1 VSH VSL ISH ISL IOCSET TSS RDSON EFFI JA JC
Notes:
(VIN = 12V, TA = 25C, unless otherwise specified)
Parameter Feedback Voltage Feedback Bias Current Switch Current Current Consumption During Power Off Line Regulation Load Regulation
Conditions IOUT = 0.1A IOUT = 0.1A -VEN = 0V VIN = 5V~18V IOUT = 0.1 to 2A
Min. 0.784 2.5 240 10 2.0 75 0.3 -
Typ. 0.8 0.1 10 1 0.2 300 20 -10 90 2 110 70 92 134 22
Max. 0.816 0.5 2 0.5 400 0.8 105 5 150 100 -
Unit V A A A % % KHz KHz V A A A ms m %
o
Oscillation Frequency Measure waveform at SW pin Frequency of Current Limit Measure waveform at SW pin or Short Circuit Protect Evaluate oscillation at SW pin EN Pin Input Voltage Evaluate oscillation stop at SW pin -EN Pin Input Leakage Current -OCSET Pin Bias Current -Soft-Start Time -VIN = 5V, VFB = 0V Internal MOSFET Rdson VIN = 12V, VFB = 0V VIN = 12V, VOUT = 5V Efficiency IOUT = 2A Thermal Resistance SOP-8L (Note 3) Junction-to-Ambient Thermal Resistance SOP-8L (Note 3) Junction-to-Case
C/W C/W
o
3. Test conditions: Device mounted on FR-4 PCB, 2"*2", 2oz copper minimum recommended pad layout, single-sided, PC boards.
AP1513 Rev. 4 DS31053
4 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Typical Performance Characteristics
AP1513 Vin vs. Frequency (Vout=3.3V; Iout=0.2A)
350 345 340 Fosc (KHz) 330 325 320 315 310 0 335
2
4
6
8 10 12 Vin (V)
14
16
18
20
0.84 0.83 0.82 0.81 0.80 0.79 0.78 0.77 0.76 0.75 0.74 0
AP1513 Vin vs. FB (Vout=3.3V; Iout=0.2A)
FB (V)
2
4
6
8
Vin (V)
10
12 14
16 18
20
3.40 3.35
AP1513 Line Regulation (Vout=3.3V; Iout=0.2A)
Vout (V)
3.25 3.20 3.15 3.10
Vout (V)
3.30
5.10 5.09 5.08 5.07 5.06 5.05 5.04 5.03 5.02 5.01 5.00 0.0
AP1513 Load Regulation (Vin=12V)
0
2
4
6
8
Vin (V)
10 12 14 16 18 20
0.5
1.0
Iout (A)
1.5
2.0
2.5
AP1513 Efficiency
100 90 80
Efficiency (%)
70 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.0 Vout:5.0V Vout:3.3V
Iout (A)
AP1513 Rev. 4 DS31053
5 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Typical Performance Characteristics
AP1513 Vout Ripple ( Vin = 12V; Vout = 3.3V; Iout = 0.1A )
(Continued)
AP1513 Vout Ripple ( Vin = 12V; Vout = 3.3V; Iout = 2A )
Test Circuit
open VCC
1K
A
OUTPUT
FB
open
Oscillation
A
VCC
OUTPUT
FB
OCSET EN VSS
1K
+ -
OCSET EN
VSS
Enable function test
33K
Feedback function test
3K
+ -
VCC
OUTPUT
FB
6.8K
OCSET EN VSS
+ -
V
1.2K
Operation function test
AP1513 Rev. 4 DS31053
6 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Functional Description
PWM Control The AP1513 is a DC/DC converter that employs pulse width modulation (PWM) scheme. Its pulse width varies in the range of 0% to 99%, based on the output current loading. The output ripple voltage caused by the PWM high frequency switching can easily be reduced through an output filter. Therefore, this converter provides a low ripple output supply over a broad range of input voltage & output current loading Under Voltage Lockout The under voltage lockout circuit of the AP1513 assures that the high-side MOSFET driver remains in the off state whenever the supply voltage drops below 3.3V. Normal operation resumes once VCC rises above 3.5V. Current Limit Protection The current limit threshold is set by external resistor ROCSET connected from VCC supply to OCSET pin. The internal sink current IOCSET (90A typical) across this resistor sets the voltage at OCSET pin. When the PWM voltage is less than the voltage at OCSET, an over-current condition is triggered. The current limit threshold is given by the following equation: Inductor Selection For most designs, the operation range with inductors is from 22H to 33H. The inductor value can be derived from the following equation:
L=
VIN - VOUT VOUT x fs x I VIN
Where IL is inductor Ripple Current. Large value inductors lower ripple current and small value inductors result in high ripple current. Choose inductor ripple current approximately 15% of the maximum load current 2A, IL=0.30A. The DC current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prevent core saturation (2A+0.15A). Input Capacitor Selection This capacitor should be located close to the IC using short leads and the voltage rating should be approximately 1.5 times the maximum input voltage. The RMS current rating requirement for the input capacitor of a buck regulator is approximately 12 the DC load current. A low ESR input capacitor sized for maximum RMS current must be used. A 470F low ESR capacitor for most applications is sufficient. Output Capacitor Selection The output capacitor is required to filter the output voltage and provides regulator loop stability. The important capacitor parameters are the 100KHz Equivalent Series Resistance (ESR), the RMS ripples current rating, voltage rating and capacitance value. For the output capacitor, the ESR value is the most important parameter. The output ripple can be calculated from the following formula.
IPEAK x R DS(ON) = IOCSET x R OCSET
(I) IPEAK > IOUT(MAX) + 2
where,
I =
VIN - VOUT VOUT x fs x L VIN
V RIPPLE = IL x ESR
The bulk capacitor's ESR will determine the output ripple voltage and the initial voltage drop after a high slew-rate transient. An aluminum electrolytic capacitor's ESR value is related to the capacitance and its voltage rating. In most case, higher voltage electrolytic capacitors have lower ESR values. Most of the time, capacitors with much higher voltage ratings may be needed to provide the low ESR values required for low output ripple voltage. PCB Layout Guide If you need low TC & TJ or large PD (Power Dissipation), The dual SW pins(5& 6) and Vss pins(7& 8)on the SOP-8L package are internally connected to die pad, The evaluation board should be allowed for maximum copper area at output (SW) pins. 1. 2. 3. 4. Connect FB circuits as closely as possible and keep away from inductor flux for pure VFB. Connect input capacitor to Vcc and Vss pin as closely as possible to get good power filter effect. Connect ROCSET to Vcc and OCSET pin as closely as possible. Connect ground side of the input capacitor & Schottky & output capacitor as closely as possible and use ground plane for best performance.
IPEAK is the output peak current; RDS (ON) is the MOSFET ON resistance; fS is the PWM frequency (300KHz typical). Also, the inductor value will affect the ripple current I. The above equation is recommended for input voltage range of 5V to 18V. For input voltage lower than 5V or ambient temperature over 100C, higher ROCSET is recommended.
AP1513 Rev. 4 DS31053
7 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
Marking Information
(1) SOP-8L
( Top View )
8 5
Logo Part Number AP1513 YY WW X X
1 4
L : Lead Free G : Green YY : Year : 08, 09,10~ WW : Week : 01~52; 52 represents 52 and 53 week X : Internal Code
Package Information
(1) Package type: SOP-8L
(All Dimensions in mm)
3.85/3.95
5.90/6.10
0.10/0.20
0.254 0.62/0.82
Gauge Plane Seating Plane
Detail "A"
7~9 1.30/1.50 1.75max. 0.15/0.25
0.35max. 45
7~9
Detail "A"
0/8
1.27typ 4.85/4.95
0.3/0.5
8x-0.60 5.4 6x-1.27 8x-1.55
Land Pattern Recommendation (Unit: mm)
AP1513 Rev. 4 DS31053
8 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated
AP1513
PWM CONTROL 2A STEP-DOWN CONVERTER
IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright (c) 2009, Diodes Incorporated www.diodes.com
AP1513 Rev. 4 DS31053
9 of 9 www.diodes.com
JULY 2009
(c) Diodes Incorporated

▲Up To Search▲

Price & Availability of AP1513SG-13

	To Download AP1513SG-13 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .